esphome-jk-bms: JK BMS B2A20S20P Heat CAN/RS485 problem with connection

Hello, I uploaded the following code for ESP8266 D1 mini and unfortunately nothing works - what am I doing wrong?

substitutions:
  name: jk-bms
  device_description: "Monitor a JK-BMS via UART-TTL"
  external_components_source: github://syssi/esphome-jk-bms@main
  tx_pin: GPIO1
  rx_pin: GPIO3

esphome:
  name: ${name}
  comment: ${device_description}
  project:
    name: "syssi.esphome-jk-bms"
    version: 1.4.0

esp8266:
  board: d1_mini

external_components:
  - source: ${external_components_source}
    refresh: 0s

api:
  encryption:
    key: "..."

ota:
  password: "..."

wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "Jk-Battery-01-Info"
    password: "..."

logger:
  baud_rate: 0
  level: DEBUG

# If you use Home Assistant please remove this `mqtt` section and uncomment the `api` component!
# The native API has many advantages over MQTT: https://esphome.io/components/api.html#advantages-over-mqtt

uart:
  - id: uart0
    baud_rate: 115200
    rx_buffer_size: 384
    tx_pin: ${tx_pin}
    rx_pin: ${rx_pin}
    debug:
     direction: BOTH

jk_modbus:
  - id: modbus0
    uart_id: uart0
    rx_timeout: 50ms

jk_bms:
  - id: bms0
    jk_modbus_id: modbus0
    update_interval: 5s

binary_sensor:
  - platform: jk_bms
    balancing:
      name: "${name} balancing"
    balancing_switch:
      name: "${name} balancing switch"
    charging:
      name: "${name} charging"
    charging_switch:
      name: "${name} charging switch"
    discharging:
      name: "${name} discharging"
    discharging_switch:
      name: "${name} discharging switch"
    dedicated_charger_switch:
      name: "${name} dedicated charger switch"
    online_status:
      name: "${name} online status"

sensor:
  - platform: jk_bms
    min_cell_voltage:
      name: "${name} min cell voltage"
    max_cell_voltage:
      name: "${name} max cell voltage"
    min_voltage_cell:
      name: "${name} min voltage cell"
    max_voltage_cell:
      name: "${name} max voltage cell"
    delta_cell_voltage:
      name: "${name} delta cell voltage"
    average_cell_voltage:
      name: "${name} average cell voltage"
    cell_voltage_1:
      name: "${name} cell voltage 1"
    cell_voltage_2:
      name: "${name} cell voltage 2"
    cell_voltage_3:
      name: "${name} cell voltage 3"
    cell_voltage_4:
      name: "${name} cell voltage 4"
    cell_voltage_5:
      name: "${name} cell voltage 5"
    cell_voltage_6:
      name: "${name} cell voltage 6"
    cell_voltage_7:
      name: "${name} cell voltage 7"
    cell_voltage_8:
      name: "${name} cell voltage 8"
    cell_voltage_9:
      name: "${name} cell voltage 9"
    cell_voltage_10:
      name: "${name} cell voltage 10"
    cell_voltage_11:
      name: "${name} cell voltage 11"
    cell_voltage_12:
      name: "${name} cell voltage 12"
    cell_voltage_13:
      name: "${name} cell voltage 13"
    cell_voltage_14:
      name: "${name} cell voltage 14"
    cell_voltage_15:
      name: "${name} cell voltage 15"
    cell_voltage_16:
      name: "${name} cell voltage 16"
    cell_voltage_17:
      name: "${name} cell voltage 17"
    cell_voltage_18:
      name: "${name} cell voltage 18"
    cell_voltage_19:
      name: "${name} cell voltage 19"
    cell_voltage_20:
      name: "${name} cell voltage 20"
    cell_voltage_21:
      name: "${name} cell voltage 21"
    cell_voltage_22:
      name: "${name} cell voltage 22"
    cell_voltage_23:
      name: "${name} cell voltage 23"
    cell_voltage_24:
      name: "${name} cell voltage 24"
    power_tube_temperature:
      name: "${name} power tube temperature"
    temperature_sensor_1:
      name: "${name} temperature sensor 1"
    temperature_sensor_2:
      name: "${name} temperature sensor 2"
    total_voltage:
      name: "${name} total voltage"
    current:
      name: "${name} current"
    power:
      name: "${name} power"
    charging_power:
      name: "${name} charging power"
    discharging_power:
      name: "${name} discharging power"
    capacity_remaining:
      name: "${name} capacity remaining"
    capacity_remaining_derived:
      name: "${name} capacity remaining derived"
    temperature_sensors:
      name: "${name} temperature sensors"
    charging_cycles:
      name: "${name} charging cycles"
    total_charging_cycle_capacity:
      name: "${name} total charging cycle capacity"
    battery_strings:
      name: "${name} battery strings"
    errors_bitmask:
      name: "${name} errors bitmask"
    operation_mode_bitmask:
      name: "${name} operation mode bitmask"
    total_voltage_overvoltage_protection:
      name: "${name} total voltage overvoltage protection"
    total_voltage_undervoltage_protection:
      name: "${name} total voltage undervoltage protection"
    cell_voltage_overvoltage_protection:
      name: "${name} cell voltage overvoltage protection"
    cell_voltage_overvoltage_recovery:
      name: "${name} cell voltage overvoltage recovery"
    cell_voltage_overvoltage_delay:
      name: "${name} cell voltage overvoltage delay"
    cell_voltage_undervoltage_protection:
      name: "${name} cell voltage undervoltage protection"
    cell_voltage_undervoltage_recovery:
      name: "${name} cell voltage undervoltage recovery"
    cell_voltage_undervoltage_delay:
      name: "${name} cell voltage undervoltage delay"
    cell_pressure_difference_protection:
      name: "${name} cell pressure difference protection"
    discharging_overcurrent_protection:
      name: "${name} discharging overcurrent protection"
    discharging_overcurrent_delay:
      name: "${name} discharging overcurrent delay"
    charging_overcurrent_protection:
      name: "${name} charging overcurrent protection"
    charging_overcurrent_delay:
      name: "${name} charging overcurrent delay"
    balance_starting_voltage:
      name: "${name} balance starting voltage"
    balance_opening_pressure_difference:
      name: "${name} balance opening pressure difference"
    power_tube_temperature_protection:
      name: "${name} power tube temperature protection"
    power_tube_temperature_recovery:
      name: "${name} power tube temperature recovery"
    temperature_sensor_temperature_protection:
      name: "${name} temperature sensor temperature protection"
    temperature_sensor_temperature_recovery:
      name: "${name} temperature sensor temperature recovery"
    temperature_sensor_temperature_difference_protection:
      name: "${name} temperature sensor temperature difference protection"
    charging_high_temperature_protection:
      name: "${name} charging high temperature protection"
    discharging_high_temperature_protection:
      name: "${name} discharging high temperature protection"
    charging_low_temperature_protection:
      name: "${name} charging low temperature protection"
    charging_low_temperature_recovery:
      name: "${name} charging low temperature recovery"
    discharging_low_temperature_protection:
      name: "${name} discharging low temperature protection"
    discharging_low_temperature_recovery:
      name: "${name} discharging low temperature recovery"
    total_battery_capacity_setting:
      name: "${name} total battery capacity setting"
    current_calibration:
      name: "${name} current calibration"
    device_address:
      name: "${name} device address"
    sleep_wait_time:
      name: "${name} sleep wait time"
    alarm_low_volume:
      name: "${name} alarm low volume"
    manufacturing_date:
      name: "${name} manufacturing date"
    total_runtime:
      name: "${name} total runtime"
#    start_current_calibration:
#      name: "${name} start current calibration"
    actual_battery_capacity:
      name: "${name} actual battery capacity"
#    protocol_version:
#      name: "${name} protocol version"

text_sensor:
  - platform: jk_bms
    errors:
      name: "${name} errors"
    operation_mode:
      name: "${name} operation mode"
    battery_type:
      name: "${name} battery type"
    password:
      name: "${name} password"
    device_type:
      name: "${name} device type"
    software_version:
      name: "${name} software version"
    manufacturer:
      name: "${name} manufacturer"
    total_runtime_formatted:
      name: "${name} total runtime formatted"

About this issue

  • Original URL
  • State: closed
  • Created 4 years ago
  • Comments: 64 (24 by maintainers)

Most upvoted comments

Most buck convertes forward full input voltage to output if they fail, so there is that danger already. In addition they could output voltage spikes if the output capacitor is small. The serial connections are very sensitiv to voltage spikes. Especially those, which can’t handle 5V logic level. (ESP, the JK-BMS are both 3.3V) And if a serial interface get’s a spike and grills the controller, usually the controller creates a short after that. -> also kills the buck converter.

So maybe you can avoid this dangers with a big capacitor after the buck converter + zener diodes which limit max voltage in addition. They need to be stronger than the converter, so they don’t break if the converter fails. 😁

@JakobTewes I cannot provide a good answer. I’m a software developer with limited skills in electrical circuits. I’m just aware of users who release magic smoke (destroyed the serial port of the BMS, ESP or buck converter).

I change device to esp32 dev and… WORKING!!! 😃 - i dont know why not working with ESP8266…

1683062868351

Hi,

I have Version 10, maybe thats the reason why i don’t have the Button.

I have also checked for an App Update, but i have latest one.

Screenshot_20230429-214649.png

Good question. In general your setup should work:

  1. Your wiring sounds correct
  2. You are using the hardware UART of an ESP8266 + the logger doesn’t write to GPIO1/3 because of baud_rate: 0
  3. You did enable the RS485 switch. This switch is new and wasn’t available in the past.

Could you enable the debug mode of the uart component and provide some logs:

logger:
  baud_rate: 0
  level: DEBUG

uart:
  id: uart0
  baud_rate: 115200
  rx_buffer_size: 384
  tx_pin: ${tx_pin}
  rx_pin: ${rx_pin}
  debug:
    direction: BOTH

I would like to know there is no response at all or noise.

Ok, when i come back from work i try it 👍🏼