esp8266_milight_hub: Domoticz 2024.7 fails with v1.13

Describe the bug

Domoticz Mi-Lights discovered via auto discovery do not respond correctly anymore. Colors can not be changed / brightness does not respond

Steps to reproduce

Install latest version of the bridge software.

Expected behavior

Domoticz should be able to control the lights as with pre FW versions.

Setup information

Firmware version

1.13

Output of http://milight-hub.local/about

"{
"firmware": "milight-hub",
"version": "1.13.0",
"ip_address": "192.xxx.xxx.xxx",
"reset_reason": "Software/System restart",
"variant": "d1_mini",
"free_heap": 14368,
"arduino_version": "3.1.2",
"free_stack": 1168,
"flash_used": 11797,
"flash_total": 957314,
"flash_pct_free": 98,
"mqtt": {
"configured": true,
"connected": true,
"status": "Connected"
},
"queue_stats": {
"length": 0,
"dropped_packets": 0
}
}"

Output of http://milight-hub.local/settings

{
	"admin_username": "idonot",
	"admin_password": "wanttosharethis",
	"ce_pin": 4,
	"csn_pin": 15,
	"reset_pin": 0,
	"led_pin": -2,
	"radio_interface_type": "nRF24",
	"packet_repeats": 75,
	"http_repeat_factor": 1,
	"auto_restart_period": 0,
	"mqtt_server": "mqtt.myserver.lan:1883",
	"mqtt_username": "top",
	"mqtt_password": "secret",
	"mqtt_topic_pattern": "milight/commands/:device_id/:device_type/:group_id",
	"mqtt_update_topic_pattern": "",
	"mqtt_state_topic_pattern": "milight/state/:device_id/:device_type/:group_id",
	"mqtt_client_status_topic": "milight/client_status",
	"simple_mqtt_client_status": true,
	"discovery_port": 48899,
	"listen_repeats": 3,
	"state_flush_interval": 10000,
	"mqtt_state_rate_limit": 500,
	"mqtt_debounce_delay": 500,
	"mqtt_retain": true,
	"packet_repeat_throttle_sensitivity": 20,
	"packet_repeat_throttle_threshold": 750,
	"packet_repeat_minimum": 100,
	"enable_automatic_mode_switching": false,
	"led_mode_wifi_config": "Fast toggle",
	"led_mode_wifi_failed": "On",
	"led_mode_operating": "Slow blip",
	"led_mode_packet": "Flicker",
	"led_mode_packet_count": 3,
	"hostname": "milight-hub",
	"rf24_power_level": "MAX",
	"rf24_listen_channel": "LOW",
	"wifi_static_ip": "",
	"wifi_static_ip_gateway": "",
	"wifi_static_ip_netmask": "",
	"packet_repeats_per_loop": 75,
	"home_assistant_discovery_prefix": "milight-discovery",
	"wifi_mode": "n",
	"default_transition_period": 500,
	"rf24_channels": [
		"LOW",
		"MID",
		"HIGH"
	],
	"device_ids": [
		2651,
		51994
	],
	"gateway_configs": [
		[
			51994,
			8899,
			5
		],
		[
			2651,
			8898,
			5
		]
	],
	"group_state_fields": [
		"state",
		"brightness",
		"computed_color",
		"mode",
		"color_temp",
		"color_mode",
		"status"
	]
}"

Additional context

I noticed the commands seems to have changed a bit: from:

{
	"state": "ON",
	"brightness": 255,
	"color": {
		"r": 255,
		"g": 255,
		"b": 255
	},
	"color_mode": "brightness",
	"status": "ON"
}

To:

{"state":"ON","color":{"r":255,"g":136,"b":100}}
{"state":"ON","brightness":148}

{"state":"ON","color":{"r":255,"g":255,"b":255}}

About this issue

  • Original URL
  • State: open
  • Created 2 years ago
  • Comments: 35 (10 by maintainers)

Most upvoted comments

@sincze The state topic is one-way and only shows the current state. You want to use the command topic to control the lights.

For reference, here is what the supported discovery configs are:

https://www.home-assistant.io/integrations/light.mqtt/#json-schema---configuration

brightness boolean (Optional, default: false) Flag that defines if light supports brightness when the rgb, rgbw, or rgbww color mode is supported.

So that should indeed be set to true.

supported_color_modes list (Optional) A list of color modes supported by the list. Possible color modes are onoff, brightness, color_temp, hs, xy, rgb, rgbw, rgbww, white. Note that if onoff or brightness are used, that must be the only value in the list.

This should not have brightness in it.