TPFanCtrl2: Failed to Read on Z16 Gen 1

When I run the program on my Z16 Gen 1 (Windows 11) I get repeated iterations of

8/2/2022 7:03:37 PM] failed to read FanSpeedLowByte 2 from EC
[8/2/2022 7:03:37 PM] failed to read FanSpeedHighByte 2 from EC
[8/2/2022 7:03:37 PM] failed to read FanSpeedLowByte 1 from EC
[8/2/2022 7:03:37 PM] failed to read FanSpeedHighByte 1 from EC

About this issue

  • Original URL
  • State: closed
  • Created 4 years ago
  • Comments: 34 (10 by maintainers)

Most upvoted comments

It works now!

[22.02.2025 10:07:02] Current Config: [22.02.2025 10:07:02] 2.3.1 Dual Fan [22.02.2025 10:07:02] Active= 2, Cycle= 5, FanBeep= 0 0, MaxReadErrors= 10 [22.02.2025 10:07:02] IconLevels= 65 75 80, NoExtSensor= 0, Lev64Norm= 1 [22.02.2025 10:07:02] Log2File= 0, Log2csv= 0, ShowAll= 0, IconColorFan= 1 [22.02.2025 10:07:02] Levels= 50° C -> 0, 60° C -> 1, 70° C -> 2, 80° C -> 4, 90° C -> 7 [22.02.2025 10:07:02] SensorOffset1-12= 0 0 0 0 0 0 0 0 0 0 0 0 ° C [22.02.2025 10:07:02] IgnoreSensors= no5, ProcessPriority= 2, IconCycle= 1 [22.02.2025 10:07:02] BluetoothEDR= 0, NoWaitMessage= 1, ShowBiasedTemps= 1 [22.02.2025 10:07:02] ManModeExit= 78, SecWinUptime= 0, SecStartDelay= 0

[22.02.2025 10:07:02] Windows uptime since boot 495 sec., SecWinUptime= 0 sec. [22.02.2025 10:07:02] Using ACPI_EC_TYPE1 [22.02.2025 10:07:04] readec: timed out #1 [22.02.2025 10:07:04] Now using ACPI_EC_TYPE2 [22.02.2025 10:07:04] failed to read status register from EC [22.02.2025 10:07:04] Change Mode from BIOS->Smart, recalculate fan speed [22.02.2025 10:07:04] Fan: 0x80 / Switch: 34° C (34; 33; 34; 0; 26; 34; 34; 0; 178; 0; 0; 0;) [22.02.2025 10:07:04] Smart: Set fan control to 0x00, Result: [i=0] OK [22.02.2025 10:07:13] Change Mode from Smart->Manual, setting fan speed [22.02.2025 10:07:13] Fan: 0x00 / Switch: 33° C (33; 33; 33; 0; 26; 33; 33; 0; 178; 0; 0; 0;) [22.02.2025 10:07:13] Manual: Set fan control to 0x07, Result: [i=0] OK

Image

Hello @FanDjango, I downloaded V2.2.5, when I try to open the .exe, there is the admin prompt but then nothing happens. I also downloaded the original TPFanControl 0.62 that still opens but works just with one fan. Can you help me maybe please?

This can happen when the .ini file is not found, make sure it’s in the same directory as the .exe (you can use the one from 2.2.0)